A ground loop isolator is also in transit and should be delivered in about a week, so I can work that in potentially.
Behringer xenyx q502usb not working Pc#
The spare parts I currently have are a male XLR to 1/4" cable, the two 1/8" to 2x 1/4" unbalanced audio cables, a female XLR to 1/8" cable and USB cords that can connect the mixer to the PC via USB. Change the setup in a way that the 1/8" to 2x 1/4" unbalanced audio cables will work and not generate noise in monitoring. Make the setup work with the new balanced audio cables and restore the fidelity of the audio.ī. My question now is, is there something I could do to either:Ī. Behringer XENYX Q502USB in stock Highlights Xenyx Mic Preamps Phantom Power: +15V Built-in One-Knob Compressors USB Audio Interface: 2-in/2-out Free. Different programs seem to have different reactions, as music being played through foobar2000 seems to not be effected as much. Spoken word is muffled and music can barely be heard, except for particular instances where it pops in and out for a split second. Particular frequencies play at regular volume, while others are extremely low or mute. However, now the fidelity of the sound is ruined.
![behringer xenyx q502usb not working behringer xenyx q502usb not working](https://audiorockstars.com/wp-content/uploads/behringer-xenyx-502-vs-q502usb-2.jpg)
I replaced the unbalanced cables with 1/8" to 1/4" cables, thinking that would fix it. I suspected that this might be a ground loop issue or interference from the equipment, since the unbalanced cables are susceptible to it.
Behringer xenyx q502usb not working tv#
I used to run 1/8" to 2x 1/4" unbalanced audio cables from the PC and TV into the mixer, but with the addition of the dbx 286s, it generated lots of noise that appeared to be coming off of lines 5/6 and 9/10, with the microphone appearing to be in perfect quality on the monitoring headphones and on recordings on the PC. This setup would allow me to have PC and TV sound coming in through the headphones, as well as monitoring for the mic. I have a pair of headphones connected to the Phones Out for monitoring. (Line 1 has FX send turned on so I can have the isolated microphone audio available for recording)
![behringer xenyx q502usb not working behringer xenyx q502usb not working](https://my-live-05.slatic.net/p/41da8f1499eee3d4608fe49ed3e73139.png)
I have a 1/8" to 1/4" cable going out of the FX Send into the PC. (phantom power button is pressed down and the red light is on. What I currently have: I got the mixer plugged in via usb in my pc and the mic via XLR also in the mixer. I have another 1/8" to 1/4" cable leading from the back of a TV into the mixer on lines 9/10 for whenever an HDMI device is connected to the TV. As the title says, im using a Behringer XENYX Q502USB mixer and a Neewer NW-700 mic and get no microphone signal on my pc. My PC audio goes out of the motherboard, leading via 1/8" to 1/4" cable to the mixer on lines 5/6.
![behringer xenyx q502usb not working behringer xenyx q502usb not working](https://cdn.shopify.com/s/files/1/2929/5648/products/MB-Q502USB_512x512.jpg)
The processed audio is output through a 1/4" to 1/8" cable, with a 1/8" adapter into the mixer on line 1. I have a XLR microphone going into a dbx 286s Mic Preamp/Processor. My mixer is a Behringer Xenyx Q1002 USB Premium.ġ. My setup is simple and complicated at the same time: